German JVAV Bearing

Send a message

Contact Us Inquiry

Product

Deep groove ball bearings

Deep groove ball bearings are the most widely used rolling bearings. They mainly bear radial load and moderate bidirectional axial load. Low friction, high speed, low noise. Available in open, 2Z metal shield, 2RS rubber seal types. Steel cage as standard, brass cage for high speed large size. Widely used in motors, pumps, fans, gearboxes.

Request a Quote
Product Details

Product Introduction

Deep groove ball bearings are the most widely used single-row ball bearings , consisting of an inner ring, an outer ring, steel balls, and a cage. The raceways of the inner and outer rings have a deep circular arc groove structure, mainly bearing radial loads, while also being able to withstand moderate axial loads in both directions . They have low frictional resistance, high limiting speed, and low operating noise.

  • Cage: Standard cage is made of stamped steel plate; large/high-speed models use solid brass cage.
  • Common suffixes:
  • Open: Open type, no seal, requires external lubrication;
  • Z / 2Z: Single-sided/double-sided steel plate dust cover;
  • RS / 2RS: Single-sided/double-sided rubber seals, pre-filled with grease at the factory, maintenance-free;
  • NR: Outer ring with retaining groove + retaining ring;
  • C3: Increased radial clearance to adapt to high temperature and interference fit assembly conditions.

Features: Simple structure, strong versatility, and high cost performance; only allows very small shaft misalignment deviations , not suitable for shafts with large deflection or severe skewness.

Application Scenarios

Motors, water pumps, fans, reducers, gearboxes; Automotive accessories: generators, air conditioning compressors; Home appliances: washing machines, air conditioners, vacuum cleaners; Agricultural machinery, textile equipment, conveyor rollers; Instruments and meters, office equipment, small general-purpose machinery.

Not recommended for heavy loads, high impacts, or large shaft deflection conditions (self-aligning roller bearings are preferred).

Installation Method

1.Clean the journal and bearing housing bore, remove burrs and rust, and measure the mating dimensions.

2.Press fitting: Inner ring tight fit → press machine presses the inner ring end face through sleeve; outer ring tight fit → press outer ring end face; direct impact on steel balls and cage is strictly prohibited .

3.Hot fitting: When the interference fit is large, heat the bearing to 80~100℃, do not exceed 120℃, and do not heat with open flame; after heating, quickly install the shaft, and lock it after cooling.

4.After assembly, the manual rotating shaft rotates smoothly without jamming; the open bearing is lubricated with grease; the 2RS sealed model cannot be disassembled.

5.No-load test run, monitoring temperature rise and noise.

Usage & Maintenance Precautions

1.Poor self-aligning capability: Only allows for slight angular deviations; cannot be used when the shaft is bent or the frame is severely deformed.

2.Differentiated by sealing type: 2RS rubber seal is suitable for dust and moisture protection, but not for high temperatures; 2Z iron dust cover is only for dust protection and is not waterproof.

3.Lubrication: Open bearings require regular grease replenishment; 2RS pre-lubrication generally requires no maintenance for life, and the seal ring should not be disassembled.

4.Clearance selection: Standard CN clearance; C3 clearance is selected for high temperature and large interference on the inner ring.

5.Storage: Store flat in a dry environment with intact rust-proof packaging; wear gloves when handling to prevent rust.

6.Impact is prohibited: Knocking or impacting will damage the steel balls and raceways, and increase vibration and noise during operation.

7.As these are precision parts, it is important to keep the assembly environment clean, as dust can quickly wear down the bearings.

Commonly Used Model Size Table (Unit: mm)

Fields: Model | d Inner Diameter | D Outer Diameter | B Width | r Minimum Chamfer | Cr Basic Dynamic Load (kN) | Cor Basic Static Load (kN) | Grease-lubricated Limiting Speed (rpm) | Weight (kg)

60 Series (narrow cross-section, compact design)

Model d D B r Cr Cor Grease Rotation Speed Weight (kg)
6000 10 26 8 0.3 4.55 1.95 29000 0.019
6001 12 28 8 0.3 5.10 2.39 26000 0.022
6002 15 32 9 0.3 5.60 2.84 22000 0.030
6003 17 35 10 0.3 6.80 3.35 20000 0.039
6004 20 42 12 0.6 9.40 4.50 17000 0.068
6005 25 47 12 0.6 10.1 5.05 14000 0.078
6006 30 55 13 1.0 13.2 6.80 11000 0.110
6007 35 62 14 1.0 16.2 8.50 9500 0.140
6008 40 68 15 1.0 17.0 9.50 8500 0.165
6009 45 75 16 1.0 21.0 12.2 7500 0.210
6010 50 80 16 1.0 22.0 13.2 6700 0.220
6011 55 90 18 1.1 28.5 17.8 6000 0.305
6012 60 95 18 1.1 31.2 19.8 5600 0.340
6013 65 100 18 1.1 31.2 20.8 5000 0.365
6014 70 110 20 1.5 38.5 25.8 4800 0.475
6015 75 115 20 1.5 40.2 27.8 4300 0.510
6016 80 125 22 1.5 47.5 32.8 4000 0.630
6017 85 130 22 1.5 50.5 35.5 3800 0.685
6018 90 140 24 2.0 58.0 41.5 3400 0.840
6019 95 145 24 2.0 60.8 45.0 3200 0.890
6020 100 150 twenty four 2.0 62.0 47.0 3000 0.950

62 series (most common, with the largest market share)

Model d D B r Cr Cor Grease Rotation Speed Weight (kg)
6200 10 30 9 0.6 5.10 2.39 26000 0.032
6201 12 32 10 0.6 6.80 3.05 24000 0.037
6202 15 35 11 0.6 7.65 3.72 20000 0.045
6203 17 40 12 0.6 9.60 4.75 18000 0.065
6204 20 47 14 1.0 12.8 6.55 15000 0.103
6205 25 52 15 1.0 14.0 7.88 13000 0.127
6206 30 62 16 1.0 19.5 11.5 10000 0.199
6207 35 72 17 1.0 25.5 15.3 8500 0.288
6208 40 80 18 1.0 30.2 19.0 7500 0.368
6209 45 85 19 1.0 32.8 21.8 6700 0.416
6210 50 90 20 1.0 35.0 23.2 6000 0.462
6211 55 100 21 1.5 43.2 29.2 5300 0.601
6212 60 110 22 1.5 47.8 32.8 4800 0.789
6213 65 120 23 1.5 55.2 38.0 4300 0.990
6214 70 125 24 1.5 60.8 45.0 4000 1.080
6215 75 130 25 1.5 66.0 49.5 3600 1.170
6216 80 140 26 2.0 72.5 55.2 3400 1.420
6217 85 150 28 2.0 83.2 63.8 3000 1.790
6218 90 160 30 2.0 92.2 71.5 2800 2.180
6219 95 170 32 2.0 102 81.8 2600 2.640
6220 100 180 34 2.0 112 92.0 2400 3.200

63 Series (Thickened version, with greater load-bearing capacity)

Model d D B r Cr Cor Grease Rotation Speed Weight (kg)
6300 10 35 11 0.6 7.65 3.47 23000 0.054
6301 12 37 12 1.0 8.10 3.92 21000 0.059
6302 15 42 13 1.0 11.4 5.43 19000 0.082
6303 17 47 14 1.0 13.5 6.55 16000 0.113
6304 20 52 15 1.0 15.9 7.80 15000 0.140
6305 25 62 17 1.0 22.5 11.4 13000 0.230
6306 30 72 19 1.0 28.1 14.6 11000 0.345
6307 35 80 21 1.5 33.2 19.2 9000 0.455
6308 40 90 23 1.5 40.8 24.0 8000 0.630
6309 45 100 25 1.5 52.8 31.8 7000 0.830
6310 50 110 27 2.0 61.8 38.0 6300 1.080
6311 55 120 29 2.0 71.5 45.0 5600 1.370
6312 60 130 31 2.0 81.8 51.8 5000 1.710
6313 65 140 33 2.0 93.8 60.5 4500 2.100
6314 70 150 35 2.0 105 68.0 4000 2.550
6315 75 160 37 2.0 112 76.5 3800 3.050
6316 80 170 39 2.0 122 86.5 3600 3.620
6317 85 180 41 2.5 132 96.5 3200 4.250
6318 90 190 43 2.5 145 108 3000 4.950
6319 95 200 45 2.5 155 120 2800 5.700
6320 100 215 47 2.5 172 140 2400 7.050

64 Series (Extra-thick and wide cross-section, strongest load-bearing capacity for the same inner diameter)

Model d D B r Cr Cor Grease Rotation Speed Weight (kg)
6403 17 62 17 1.1 22.3 10.8 11000 0.240
6404 20 72 19 1.1 31.0 15.2 9500 0.370
6405 25 80 21 1.5 38.2 19.2 8500 0.510
6406 30 90 23 1.5 47.5 24.0 7500 0.720
6407 35 100 25 1.5 56.8 29.5 6300 0.960
6408 40 110 27 2.0 65.5 37.5 6000 1.240
6409 45 120 29 2.0 77.5 45.5 5300 1.550
6410 50 130 31 2.0 83.2 50.5 4800 1.910
6411 55 140 33 2.0 95.2 59.2 4300 2.300
6412 60 150 35 2.0 108 70.0 4000 2.810
6413 65 160 37 2.0 118 78.5 3600 3.350
6414 70 180 42 2.5 142 96.5 3200 4.400
6415 75 190 45 2.5 155 108 3000 5.180
6416 80 200 48 2.5 165 115 2800 5.980
6417 85 210 52 3.0 178 132 2600 7.070
6418 90 225 54 3.0 192 145 2400 8.200
6419 95 240 55 3.0 208 165 2200 9.200
6420 100 250 58 3.0 228 182 2000 10.50

Ask About This Bearing.

Send us your specifications and operating conditions to discuss whether this bearing suits your application.

Send inquiry