Product
Tapered Roller Bearings
Tapered roller bearings are separable bearings , consisting of an inner ring assembly (rollers + cage + inner ring) and an outer ring, which can be installed separately. The rolling elements are tapered rollers, and the raceways are tapered, enabling them to withstand radial loads and unidirectional axial loads simultaneously .
Product Introduction
Tapered roller bearings are separable bearings , consisting of an inner ring assembly (rollers + cage + inner ring) and an outer ring, which can be installed separately. The rolling elements are tapered rollers, and the raceways are tapered, enabling them to withstand radial loads and unidirectional axial loads simultaneously . They have high load-carrying capacity, good rigidity, and can restrict unidirectional axial displacement of the shaft; when used in pairs, they can withstand bidirectional axial forces and restrict bidirectional shaft movement. Common cage types include stamped steel cages and solid brass cages. (Note: The last sentence about suffixes is a separate, unrelated point and can be omitted.)
- 30000 Series: National Standard Series;
- X: External dimensions conform to ISO standards;
- J: Outer ring taper matching;
Application Scenarios
Equipment that simultaneously withstands radial and axial combined loads:
- Automobiles: differential, transmission, wheel hubs
- speed reducer, gearbox
- Construction machinery: excavators, loaders
- Mining equipment, cranes
- Steel rolling equipment, paper making machine
- Pumps, air compressors
- machine tool spindle
Not recommended for: pure axial loads, extremely high speed conditions (roller sliding friction, limiting speed lower than ball bearings).
Installation Method
- Parts inspection : Separate the inner component from the outer ring, clean the journal and bearing housing bore, remove burrs, and measure the mating dimensions.
- Assembly sequence : First, press the inner ring assembly onto the shaft; then install the outer ring into the bearing housing hole. Pressing can only be performed on the end face of the inner ring (shaft mounting) or the end face of the outer ring (housing mounting); direct impact on the rollers is strictly prohibited .
- After installation, manually rotate the shaft; it should rotate smoothly without jamming. Add grease/oil.
- No-load test run, monitoring temperature rise and noise.
Hot fitting instructions: The internal components should be hot fitted at a temperature of 80~120℃, and open flame heating is prohibited; the outer ring should be assembled at room temperature.
1.Parts inspection : Separate the inner component from the outer ring, clean the journal and bearing housing bore, remove burrs, and measure the mating dimensions.
2.Assembly sequence : First, press the inner ring assembly onto the shaft; then install the outer ring into the bearing housing hole. Pressing can only be performed on the end face of the inner ring (shaft mounting) or the end face of the outer ring (housing mounting); direct impact on the rollers is strictly prohibited .
3.After installation, manually rotate the shaft; it should rotate smoothly without jamming. Add grease/oil.
4.No-load test run, monitoring temperature rise and noise.
Hot fitting instructions: The internal components should be hot fitted at a temperature of 80~120℃, and open flame heating is prohibited; the outer ring should be assembled at room temperature.
Usage & Maintenance Precautions
- Pairing principle : A single tapered roller bearing can only withstand unidirectional axial force; to withstand bidirectional axial loads, they must be installed in pairs.
- Clearance control : The factory clearance cannot be directly used as the working clearance; it must be adjusted after assembly. Increased temperature will reduce the clearance. Standard CN clearance; C3 clearance is selected for high-temperature and heavy-load conditions.
- Lubrication requirements : Rollers have sliding friction, and poor lubrication can easily lead to wear and burning; regular grease replenishment or oil changes are necessary.
- Impact is prohibited : Knocking and impact will cause indentations on the rollers and raceways, and increase vibration and noise during operation.
- Storage : Store in a dry, dark place, flat. Keep internal components and outer rings separate and do not mix them. Wear gloves to prevent rust.
- Fit selection : The rotating inner ring uses a tight fit; the stationary outer ring can use a loose fit.
- Disassembly : Separable bearings are easy to disassemble, but the inner components and outer rings are not interchangeable . The inner and outer rings of the same set of bearings must be used in combination. Do not mix the inner and outer rings of different bearings.
Commonly Used Model Dimensions Table (GB/T297, Unit: mm)
Fields: Model | d Inner Diameter | D Outer Diameter | T Total Thickness | B Inner Ring Width | C Outer Ring Width | r Minimum Chamfer | Cr Basic Dynamic Load ( kN ) | Cor Basic Static Load ( kN ) | Grease Lubrication Limiting Speed (rpm) | Reference Weight (kg)
302 Series (Most General Purpose, Medium Load)
| Model | d | D | T | B | C | r | Cr | Cor | Grease Rotation Speed | Weight (kg) |
| 30204 | 20 | 47 | 15.25 | 14 | 12 | 1.0 | 28.2 | 30.5 | 7500 | 0.127 |
| 30205 | 25 | 52 | 16.25 | 15 | 13 | 1.0 | 32.2 | 37.0 | 6300 | 0.160 |
| 30206 | 30 | 62 | 17.25 | 16 | 14 | 1.0 | 43.2 | 50.5 | 5300 | 0.230 |
| 30207 | 35 | 72 | 18.25 | 17 | 15 | 1.5 | 54.2 | 63.5 | 4500 | 0.310 |
| 30208 | 40 | 80 | 19.75 | 18 | 16 | 1.5 | 63.0 | 74.0 | 4000 | 0.400 |
| 30209 | 45 | 85 | 20.75 | 19 | 16 | 1.5 | 67.8 | 83.5 | 3600 | 0.440 |
| 30210 | 50 | 90 | 21.75 | 20 | 17 | 1.5 | 73.2 | 92.0 | 3400 | 0.510 |
| 30211 | 55 | 100 | 22.75 | 21 | 18 | 2.0 | 90.8 | 115 | 3000 | 0.660 |
| 30212 | 60 | 110 | 23.75 | 22 | 19 | 2.0 | 102 | 130 | 2800 | 0.820 |
| 30213 | 65 | 120 | 24.75 | 23 | 20 | 2.0 | 115 | 150 | 2400 | 1.03 |
| 30214 | 70 | 125 | 26.25 | 24 | 21 | 2.0 | 128 | 172 | 2200 | 1.19 |
| 30215 | 75 | 130 | 27.25 | 25 | twenty two | 2.0 | 138 | 188 | 2000 | 1.33 |
303 Series (Heavy-duty model, with greater load capacity)
| Model | d | D | T | B | C | r | Cr | Cor | Grease Rotation Speed | Weight (kg) |
| 30304 | 20 | 52 | 16.25 | 15 | 13 | 1.5 | 33.0 | 33.2 | 7000 | 0.165 |
| 30305 | 25 | 62 | 18.25 | 17 | 15 | 1.5 | 46.0 | 48.0 | 5600 | 0.260 |
| 30306 | 30 | 72 | 20.75 | 19 | 16 | 1.5 | 59.0 | 63.0 | 4800 | 0.380 |
| 30307 | 35 | 80 | 22.75 | 21 | 18 | 2.0 | 72.2 | 78.2 | 4200 | 0.510 |
| 30308 | 40 | 90 | 25.25 | 23 | 20 | 2.0 | 90.8 | 98.0 | 3600 | 0.740 |
| 30309 | 45 | 100 | 27.25 | 25 | 22 | 2.0 | 108 | 118 | 3200 | 0.980 |
| 30310 | 50 | 110 | 29.25 | 27 | 23 | 2.5 | 130 | 142 | 3000 | 1.27 |
322 Series (Wide cross-section, stronger radial load capacity)
| Model | d | D | T | B | C | r | Cr | Cor | Grease Rotation Speed | Weight (kg) |
| 32206 | 30 | 62 | 21.25 | 20 | 17 | 1.0 | 51.8 | 63.8 | 5000 | 0.288 |
| 32207 | 35 | 72 | 24.25 | twenty three | 19 | 1.5 | 70.5 | 87.2 | 4300 | 0.427 |
| 32208 | 40 | 80 | 24.75 | 23 | 19 | 1.5 | 77.8 | 96.5 | 3800 | 0.515 |
| 32209 | 45 | 85 | 24.75 | 23 | 19 | 1.5 | 80.2 | 102 | 3400 | 0.552 |
| 32210 | 50 | 90 | 24.75 | 23 | 19 | 1.5 | 82.5 | 108 | 3200 | 0.590 |
| 32211 | 55 | 100 | 26.75 | 25 | twenty one | 2.0 | 105 | 138 | 2800 | 0.780 |
323 Series (Extra-wide and Heavy-duty, High Impact Load)
| Model | d | D | T | B | C | r | Cr | Cor | Grease Rotation Speed | Weight (kg) |
| 32308 | 40 | 90 | 35.25 | 33 | 27 | 2.0 | 132 | 160 | 3200 | 1.07 |
| 32309 | 45 | 100 | 38.25 | 36 | 30 | 2.0 | 158 | 192 | 2800 | 1.44 |
| 32310 | 50 | 110 | 42.25 | 40 | 33 | 2.5 | 192 | 235 | 2600 | 1.91 |