German JVAV Bearing

Send a message

Contact Us Inquiry

Product

Self-aligning roller bearings

Self-aligning roller bearings are double-row spherical roller bearings . The outer ring raceway has a spherical structure with two rows of symmetrical spherical rollers, providing self-aligning capability.

Request a Quote
Product Details

Product Introduction

Self-aligning roller bearings are double-row spherical roller bearings . The outer ring raceway has a spherical structure with two rows of symmetrical spherical rollers, providing self-aligning capability. This allows for a 1.5~2.5° tilt between the inner and outer rings , compensating for coaxiality deviations such as shaft deflection, frame deformation, and installation misalignment. They are designed for extremely high radial loads and can also withstand moderate bidirectional axial loads. They offer strong shock and vibration resistance, making them suitable for heavy-duty vibration applications. Their limiting speed is lower than that of self-aligning ball bearings. Two types of inner bores are available:

  1. Cylindrical hole: Directly mounted on the stepped shaft;
  2. The conical bore (suffix K, taper 1:12; K30=1:30 large taper) is paired with a locking sleeve/removal sleeve for easy installation of the optical shaft and adjustment of radial clearance.

Common suffixes:

  • CA: Brass solid cage;
  • CC: Stamped steel cage, internally optimized;
  • W33: Outer ring with oil groove + 3 lubrication holes for easy continuous oil replenishment; Standard: GB/T288-2013, ISO international standard.

Application Scenarios

Heavy-duty, vibrating, shaft-bending, and difficult-to-align equipment:

  • Mining equipment: crushers, ball mills, screening machines
  • Metallurgical equipment: rolling mills, roller conveyors
  • Conveyors: Heavy-duty belt conveyors, bucket elevators
  • Papermaking machinery, cement equipment, centrifuges
  • Fans (large industrial fans), water pumps
  • Vibrating screen, tunnel boring equipment, gearbox

Not recommended for high-speed, light-load conditions (self-aligning ball bearings should be preferred).

Installation Method

Cylindrical bore self-aligning roller bearing

1.Clean the journal and bearing housing bore, remove burrs and rust, and measure the mating dimensions;

2.Apply lubricant to the mating surfaces;

3.Small interference fit: Press machine + copper bushing, only press the inner ring end face for shaft installation; press the outer ring end face for installation into bearing housing, and strictly prohibit striking the rollers and cage ;

4.Large interference fit: Hot charge, heat to 80–120℃, open flame is prohibited, temperature should not exceed 130℃ to prevent tempering failure;

5.After the bearing is in place, do not immediately tighten the end cover. Manually rotate the shaft several times to allow the bearing to automatically align before tightening and fixing it.

6.Add lubricating grease, run under no-load test, and monitor temperature rise and vibration.

Conical hole (K type) + locknut installation

1.Insert the locking sleeve into the optical shaft and push the bearing into the locking sleeve;

2.Rotate the lock nut to push the bearing, and control the interference by reducing the radial clearance (this is very important; if it is too tight, the bearing may overheat and burn out).

3.After installation, radial clearance must be measured to confirm that the clearance meets the standard.

4.Locking anti-loosening washer/anti-loosening nut.

The core principle of installation is that force should not be transmitted through the rollers to avoid damaging the raceways.

Usage & Maintenance Precautions

1.Self-alignment limit : Maximum allowable tilt is 1.5~2.5°, exceeding the angle will drastically shorten the lifespan;

2.Load characteristics : Primarily radial under heavy loads, can withstand medium axial loads in both directions, but not suitable for pure large axial loads.

3.Lubrication is crucial : heavy-duty rollers experience high friction and require adequate and clean lubrication; the W33 oil groove model allows for online grease replenishment; aged grease and impurities can quickly cause bearing failure.

4.Temperature control : The recommended long-term operating temperature is below 100℃; the temperature for hot-fitting should not exceed 130℃.

5.Clearance selection : Standard CN clearance; C3 for high temperature, large interference, and vibration conditions; C4 for heavy impact loads;

6.Storage : Store in a dry, dark place, do not stack or compress; wear gloves when handling to prevent corrosion from sweat.

7.Fit selection : Use a tight fit for the inner ring; use a loose fit for the outer ring when compensating for movement.

8.Impact is prohibited : Knocking or heavy object impact will cause indentations on the rollers and raceways, and excessive vibration during operation.

Commonly Used Model Dimensions Table (GB/T288-2013, Unit: mm)

Fields: Model | d Inner Diameter | D Outer Diameter | B Width | r Minimum Chamfer | Cr Basic Dynamic Load (kN) | Cor Basic Static Load (kN) | Grease-lubricated Limiting Speed (rpm) | Reference Weight (kg)

Suffix K = conical bore; W33 outer ring oil groove/oil hole; CC/CA cage structure

213 Series (Narrow cross-section, compact space)

Model d D B r Cr Cor Grease Rotation Speed Weight (kg)
21305 25 62 17 1.0 44.2 44.8 5300 0.27
21306 30 72 19 1.0 57.2 58.5 4500 0.39
21307 35 80 21 1.0 69.5 72.2 3800 0.52
21308 40 90 23 1.0 86.5 90.8 3400 0.71
21309 45 100 25 1.0 102 108 3000 0.96
21310 50 110 27 1.5 122 130 2700 1.26
21311 55 120 29 1.5 142 152 2400 1.62
21312 60 130 31 1.5 162 175 2200 2.04

222 series (general-purpose wide type, most commonly used in the market)

Model d D B r Cr Cor Grease Rotation Speed Weight (kg)
22205 25 52 18 1.0 36.8 36.8 8000 0.177
22206 30 62 20 1.0 51.8 55.0 6700 0.283
22207 35 72 23 1.0 70.2 79.0 5600 0.437
22208 40 80 23 1.0 79.0 88.5 5000 0.524
22209 45 85 23 1.0 82.8 95.2 4500 0.571
22210 50 90 23 1.0 86.0 102 4300 0.614
22211 55 100 25 1.5 114 138 3800 0.897
22212 60 110 28 1.5 142 172 3400 1.21
22213 65 120 31 1.5 172 208 3000 1.64
22214 70 125 31 1.5 182 222 2800 1.75
22215 75 130 31 1.5 188 235 2600 1.85
22216 80 140 33 2.0 212 268 2400 2.30
22217 85 150 36 2.0 242 308 2200 2.90
22218 90 160 40 2.0 280 358 2000 3.70
22219 95 170 43 2.0 322 415 1900 4.55
22220 100 180 46 2.0 370 480 1800 5.40

223 Series (Extra-wide, the first choice for heavy-duty impact resistance)

Model d D B r Cr Cor Grease Rotation Speed Weight (kg)
22308 40 90 33 1.5 132 138 3800 1.02
22309 45 100 36 1.5 158 170 3400 1.37
22310 50 110 40 2.0 192 208 3000 1.86
22311 55 120 43 2.0 228 248 2800 2.40
22312 60 130 46 2.0 260 285 2400 3.02
22313 65 140 48 2.0 288 320 2200 3.68
22314 70 150 51 2.0 325 365 2000 4.45
22315 75 160 55 2.0 368 415 1900 5.40
22316 80 170 58 2.0 412 465 1700 6.45
22317 85 180 60 2.5 450 520 1600 7.45
22318 90 190 64 2.5 500 578 1500 8.70
22319 95 200 67 2.5 542 640 1400 10.10
22320 100 215 73 2.5 620 730 1300 12.20

230 Series (Thin cross-section, large outer diameter, space-constrained heavy-duty)

Model d D B r Cr Cor Grease Rotation Speed Weight (kg)
23024 120 180 46 2.0 310 465 1700 4.10
23026 130 200 52 2.0 370 560 1500 5.60
23028 140 210 53 2.0 405 620 1400 6.20
23030 150 225 56 2.1 450 695 1300 7.50

Ask About This Bearing.

Send us your specifications and operating conditions to discuss whether this bearing suits your application.

Send inquiry