Product
Deep groove ball bearings
Deep groove ball bearings are the most widely used rolling bearings. They mainly bear radial load and moderate bidirectional axial load. Low friction, high speed, low noise. Available in open, 2Z metal shield, 2RS rubber seal types. Steel cage as standard, brass cage for high speed large size. Widely used in motors, pumps, fans, gearboxes.
Product Introduction
Deep groove ball bearings are the most widely used single-row ball bearings , consisting of an inner ring, an outer ring, steel balls, and a cage. The raceways of the inner and outer rings have a deep circular arc groove structure, mainly bearing radial loads, while also being able to withstand moderate axial loads in both directions . They have low frictional resistance, high limiting speed, and low operating noise.
- Cage: Standard cage is made of stamped steel plate; large/high-speed models use solid brass cage.
- Common suffixes:
- Open: Open type, no seal, requires external lubrication;
- Z / 2Z: Single-sided/double-sided steel plate dust cover;
- RS / 2RS: Single-sided/double-sided rubber seals, pre-filled with grease at the factory, maintenance-free;
- NR: Outer ring with retaining groove + retaining ring;
- C3: Increased radial clearance to adapt to high temperature and interference fit assembly conditions.
Features: Simple structure, strong versatility, and high cost performance; only allows very small shaft misalignment deviations , not suitable for shafts with large deflection or severe skewness.
Application Scenarios
Motors, water pumps, fans, reducers, gearboxes; Automotive accessories: generators, air conditioning compressors; Home appliances: washing machines, air conditioners, vacuum cleaners; Agricultural machinery, textile equipment, conveyor rollers; Instruments and meters, office equipment, small general-purpose machinery.
Not recommended for heavy loads, high impacts, or large shaft deflection conditions (self-aligning roller bearings are preferred).
Installation Method
1.Clean the journal and bearing housing bore, remove burrs and rust, and measure the mating dimensions.
2.Press fitting: Inner ring tight fit → press machine presses the inner ring end face through sleeve; outer ring tight fit → press outer ring end face; direct impact on steel balls and cage is strictly prohibited .
3.Hot fitting: When the interference fit is large, heat the bearing to 80~100℃, do not exceed 120℃, and do not heat with open flame; after heating, quickly install the shaft, and lock it after cooling.
4.After assembly, the manual rotating shaft rotates smoothly without jamming; the open bearing is lubricated with grease; the 2RS sealed model cannot be disassembled.
5.No-load test run, monitoring temperature rise and noise.
Usage & Maintenance Precautions
1.Poor self-aligning capability: Only allows for slight angular deviations; cannot be used when the shaft is bent or the frame is severely deformed.
2.Differentiated by sealing type: 2RS rubber seal is suitable for dust and moisture protection, but not for high temperatures; 2Z iron dust cover is only for dust protection and is not waterproof.
3.Lubrication: Open bearings require regular grease replenishment; 2RS pre-lubrication generally requires no maintenance for life, and the seal ring should not be disassembled.
4.Clearance selection: Standard CN clearance; C3 clearance is selected for high temperature and large interference on the inner ring.
5.Storage: Store flat in a dry environment with intact rust-proof packaging; wear gloves when handling to prevent rust.
6.Impact is prohibited: Knocking or impacting will damage the steel balls and raceways, and increase vibration and noise during operation.
7.As these are precision parts, it is important to keep the assembly environment clean, as dust can quickly wear down the bearings.
Commonly Used Model Size Table (Unit: mm)
Fields: Model | d Inner Diameter | D Outer Diameter | B Width | r Minimum Chamfer | Cr Basic Dynamic Load (kN) | Cor Basic Static Load (kN) | Grease-lubricated Limiting Speed (rpm) | Weight (kg)
60 Series (narrow cross-section, compact design)
| Model | d | D | B | r | Cr | Cor | Grease Rotation Speed | Weight (kg) |
| 6000 | 10 | 26 | 8 | 0.3 | 4.55 | 1.95 | 29000 | 0.019 |
| 6001 | 12 | 28 | 8 | 0.3 | 5.10 | 2.39 | 26000 | 0.022 |
| 6002 | 15 | 32 | 9 | 0.3 | 5.60 | 2.84 | 22000 | 0.030 |
| 6003 | 17 | 35 | 10 | 0.3 | 6.80 | 3.35 | 20000 | 0.039 |
| 6004 | 20 | 42 | 12 | 0.6 | 9.40 | 4.50 | 17000 | 0.068 |
| 6005 | 25 | 47 | 12 | 0.6 | 10.1 | 5.05 | 14000 | 0.078 |
| 6006 | 30 | 55 | 13 | 1.0 | 13.2 | 6.80 | 11000 | 0.110 |
| 6007 | 35 | 62 | 14 | 1.0 | 16.2 | 8.50 | 9500 | 0.140 |
| 6008 | 40 | 68 | 15 | 1.0 | 17.0 | 9.50 | 8500 | 0.165 |
| 6009 | 45 | 75 | 16 | 1.0 | 21.0 | 12.2 | 7500 | 0.210 |
| 6010 | 50 | 80 | 16 | 1.0 | 22.0 | 13.2 | 6700 | 0.220 |
| 6011 | 55 | 90 | 18 | 1.1 | 28.5 | 17.8 | 6000 | 0.305 |
| 6012 | 60 | 95 | 18 | 1.1 | 31.2 | 19.8 | 5600 | 0.340 |
| 6013 | 65 | 100 | 18 | 1.1 | 31.2 | 20.8 | 5000 | 0.365 |
| 6014 | 70 | 110 | 20 | 1.5 | 38.5 | 25.8 | 4800 | 0.475 |
| 6015 | 75 | 115 | 20 | 1.5 | 40.2 | 27.8 | 4300 | 0.510 |
| 6016 | 80 | 125 | 22 | 1.5 | 47.5 | 32.8 | 4000 | 0.630 |
| 6017 | 85 | 130 | 22 | 1.5 | 50.5 | 35.5 | 3800 | 0.685 |
| 6018 | 90 | 140 | 24 | 2.0 | 58.0 | 41.5 | 3400 | 0.840 |
| 6019 | 95 | 145 | 24 | 2.0 | 60.8 | 45.0 | 3200 | 0.890 |
| 6020 | 100 | 150 | twenty four | 2.0 | 62.0 | 47.0 | 3000 | 0.950 |
62 series (most common, with the largest market share)
| Model | d | D | B | r | Cr | Cor | Grease Rotation Speed | Weight (kg) |
| 6200 | 10 | 30 | 9 | 0.6 | 5.10 | 2.39 | 26000 | 0.032 |
| 6201 | 12 | 32 | 10 | 0.6 | 6.80 | 3.05 | 24000 | 0.037 |
| 6202 | 15 | 35 | 11 | 0.6 | 7.65 | 3.72 | 20000 | 0.045 |
| 6203 | 17 | 40 | 12 | 0.6 | 9.60 | 4.75 | 18000 | 0.065 |
| 6204 | 20 | 47 | 14 | 1.0 | 12.8 | 6.55 | 15000 | 0.103 |
| 6205 | 25 | 52 | 15 | 1.0 | 14.0 | 7.88 | 13000 | 0.127 |
| 6206 | 30 | 62 | 16 | 1.0 | 19.5 | 11.5 | 10000 | 0.199 |
| 6207 | 35 | 72 | 17 | 1.0 | 25.5 | 15.3 | 8500 | 0.288 |
| 6208 | 40 | 80 | 18 | 1.0 | 30.2 | 19.0 | 7500 | 0.368 |
| 6209 | 45 | 85 | 19 | 1.0 | 32.8 | 21.8 | 6700 | 0.416 |
| 6210 | 50 | 90 | 20 | 1.0 | 35.0 | 23.2 | 6000 | 0.462 |
| 6211 | 55 | 100 | 21 | 1.5 | 43.2 | 29.2 | 5300 | 0.601 |
| 6212 | 60 | 110 | 22 | 1.5 | 47.8 | 32.8 | 4800 | 0.789 |
| 6213 | 65 | 120 | 23 | 1.5 | 55.2 | 38.0 | 4300 | 0.990 |
| 6214 | 70 | 125 | 24 | 1.5 | 60.8 | 45.0 | 4000 | 1.080 |
| 6215 | 75 | 130 | 25 | 1.5 | 66.0 | 49.5 | 3600 | 1.170 |
| 6216 | 80 | 140 | 26 | 2.0 | 72.5 | 55.2 | 3400 | 1.420 |
| 6217 | 85 | 150 | 28 | 2.0 | 83.2 | 63.8 | 3000 | 1.790 |
| 6218 | 90 | 160 | 30 | 2.0 | 92.2 | 71.5 | 2800 | 2.180 |
| 6219 | 95 | 170 | 32 | 2.0 | 102 | 81.8 | 2600 | 2.640 |
| 6220 | 100 | 180 | 34 | 2.0 | 112 | 92.0 | 2400 | 3.200 |
63 Series (Thickened version, with greater load-bearing capacity)
| Model | d | D | B | r | Cr | Cor | Grease Rotation Speed | Weight (kg) |
| 6300 | 10 | 35 | 11 | 0.6 | 7.65 | 3.47 | 23000 | 0.054 |
| 6301 | 12 | 37 | 12 | 1.0 | 8.10 | 3.92 | 21000 | 0.059 |
| 6302 | 15 | 42 | 13 | 1.0 | 11.4 | 5.43 | 19000 | 0.082 |
| 6303 | 17 | 47 | 14 | 1.0 | 13.5 | 6.55 | 16000 | 0.113 |
| 6304 | 20 | 52 | 15 | 1.0 | 15.9 | 7.80 | 15000 | 0.140 |
| 6305 | 25 | 62 | 17 | 1.0 | 22.5 | 11.4 | 13000 | 0.230 |
| 6306 | 30 | 72 | 19 | 1.0 | 28.1 | 14.6 | 11000 | 0.345 |
| 6307 | 35 | 80 | 21 | 1.5 | 33.2 | 19.2 | 9000 | 0.455 |
| 6308 | 40 | 90 | 23 | 1.5 | 40.8 | 24.0 | 8000 | 0.630 |
| 6309 | 45 | 100 | 25 | 1.5 | 52.8 | 31.8 | 7000 | 0.830 |
| 6310 | 50 | 110 | 27 | 2.0 | 61.8 | 38.0 | 6300 | 1.080 |
| 6311 | 55 | 120 | 29 | 2.0 | 71.5 | 45.0 | 5600 | 1.370 |
| 6312 | 60 | 130 | 31 | 2.0 | 81.8 | 51.8 | 5000 | 1.710 |
| 6313 | 65 | 140 | 33 | 2.0 | 93.8 | 60.5 | 4500 | 2.100 |
| 6314 | 70 | 150 | 35 | 2.0 | 105 | 68.0 | 4000 | 2.550 |
| 6315 | 75 | 160 | 37 | 2.0 | 112 | 76.5 | 3800 | 3.050 |
| 6316 | 80 | 170 | 39 | 2.0 | 122 | 86.5 | 3600 | 3.620 |
| 6317 | 85 | 180 | 41 | 2.5 | 132 | 96.5 | 3200 | 4.250 |
| 6318 | 90 | 190 | 43 | 2.5 | 145 | 108 | 3000 | 4.950 |
| 6319 | 95 | 200 | 45 | 2.5 | 155 | 120 | 2800 | 5.700 |
| 6320 | 100 | 215 | 47 | 2.5 | 172 | 140 | 2400 | 7.050 |
64 Series (Extra-thick and wide cross-section, strongest load-bearing capacity for the same inner diameter)
| Model | d | D | B | r | Cr | Cor | Grease Rotation Speed | Weight (kg) |
| 6403 | 17 | 62 | 17 | 1.1 | 22.3 | 10.8 | 11000 | 0.240 |
| 6404 | 20 | 72 | 19 | 1.1 | 31.0 | 15.2 | 9500 | 0.370 |
| 6405 | 25 | 80 | 21 | 1.5 | 38.2 | 19.2 | 8500 | 0.510 |
| 6406 | 30 | 90 | 23 | 1.5 | 47.5 | 24.0 | 7500 | 0.720 |
| 6407 | 35 | 100 | 25 | 1.5 | 56.8 | 29.5 | 6300 | 0.960 |
| 6408 | 40 | 110 | 27 | 2.0 | 65.5 | 37.5 | 6000 | 1.240 |
| 6409 | 45 | 120 | 29 | 2.0 | 77.5 | 45.5 | 5300 | 1.550 |
| 6410 | 50 | 130 | 31 | 2.0 | 83.2 | 50.5 | 4800 | 1.910 |
| 6411 | 55 | 140 | 33 | 2.0 | 95.2 | 59.2 | 4300 | 2.300 |
| 6412 | 60 | 150 | 35 | 2.0 | 108 | 70.0 | 4000 | 2.810 |
| 6413 | 65 | 160 | 37 | 2.0 | 118 | 78.5 | 3600 | 3.350 |
| 6414 | 70 | 180 | 42 | 2.5 | 142 | 96.5 | 3200 | 4.400 |
| 6415 | 75 | 190 | 45 | 2.5 | 155 | 108 | 3000 | 5.180 |
| 6416 | 80 | 200 | 48 | 2.5 | 165 | 115 | 2800 | 5.980 |
| 6417 | 85 | 210 | 52 | 3.0 | 178 | 132 | 2600 | 7.070 |
| 6418 | 90 | 225 | 54 | 3.0 | 192 | 145 | 2400 | 8.200 |
| 6419 | 95 | 240 | 55 | 3.0 | 208 | 165 | 2200 | 9.200 |
| 6420 | 100 | 250 | 58 | 3.0 | 228 | 182 | 2000 | 10.50 |