German JVAV Bearing

Send a message

Contact Us Inquiry

Product

Tapered Roller Bearings

Tapered roller bearings are separable bearings , consisting of an inner ring assembly (rollers + cage + inner ring) and an outer ring, which can be installed separately. The rolling elements are tapered rollers, and the raceways are tapered, enabling them to withstand radial loads and unidirectional axial loads simultaneously .

Request a Quote
Product Details

Product Introduction

Tapered roller bearings are separable bearings , consisting of an inner ring assembly (rollers + cage + inner ring) and an outer ring, which can be installed separately. The rolling elements are tapered rollers, and the raceways are tapered, enabling them to withstand radial loads and unidirectional axial loads simultaneously . They have high load-carrying capacity, good rigidity, and can restrict unidirectional axial displacement of the shaft; when used in pairs, they can withstand bidirectional axial forces and restrict bidirectional shaft movement. Common cage types include stamped steel cages and solid brass cages. (Note: The last sentence about suffixes is a separate, unrelated point and can be omitted.)

  • 30000 Series: National Standard Series;
  • X: External dimensions conform to ISO standards;
  • J: Outer ring taper matching;

Application Scenarios

Equipment that simultaneously withstands radial and axial combined loads:

  • Automobiles: differential, transmission, wheel hubs
  • speed reducer, gearbox
  • Construction machinery: excavators, loaders
  • Mining equipment, cranes
  • Steel rolling equipment, paper making machine
  • Pumps, air compressors
  • machine tool spindle

Not recommended for: pure axial loads, extremely high speed conditions (roller sliding friction, limiting speed lower than ball bearings).

Installation Method

  1. Parts inspection : Separate the inner component from the outer ring, clean the journal and bearing housing bore, remove burrs, and measure the mating dimensions.
  2. Assembly sequence : First, press the inner ring assembly onto the shaft; then install the outer ring into the bearing housing hole. Pressing can only be performed on the end face of the inner ring (shaft mounting) or the end face of the outer ring (housing mounting); direct impact on the rollers is strictly prohibited .
  3. After installation, manually rotate the shaft; it should rotate smoothly without jamming. Add grease/oil.
  4. No-load test run, monitoring temperature rise and noise.

Hot fitting instructions: The internal components should be hot fitted at a temperature of 80~120℃, and open flame heating is prohibited; the outer ring should be assembled at room temperature.

1.Parts inspection : Separate the inner component from the outer ring, clean the journal and bearing housing bore, remove burrs, and measure the mating dimensions.

2.Assembly sequence : First, press the inner ring assembly onto the shaft; then install the outer ring into the bearing housing hole. Pressing can only be performed on the end face of the inner ring (shaft mounting) or the end face of the outer ring (housing mounting); direct impact on the rollers is strictly prohibited .

3.After installation, manually rotate the shaft; it should rotate smoothly without jamming. Add grease/oil.

4.No-load test run, monitoring temperature rise and noise.

Hot fitting instructions: The internal components should be hot fitted at a temperature of 80~120℃, and open flame heating is prohibited; the outer ring should be assembled at room temperature.

Usage & Maintenance Precautions

  1. Pairing principle : A single tapered roller bearing can only withstand unidirectional axial force; to withstand bidirectional axial loads, they must be installed in pairs.
  2. Clearance control : The factory clearance cannot be directly used as the working clearance; it must be adjusted after assembly. Increased temperature will reduce the clearance. Standard CN clearance; C3 clearance is selected for high-temperature and heavy-load conditions.
  3. Lubrication requirements : Rollers have sliding friction, and poor lubrication can easily lead to wear and burning; regular grease replenishment or oil changes are necessary.
  4. Impact is prohibited : Knocking and impact will cause indentations on the rollers and raceways, and increase vibration and noise during operation.
  5. Storage : Store in a dry, dark place, flat. Keep internal components and outer rings separate and do not mix them. Wear gloves to prevent rust.
  6. Fit selection : The rotating inner ring uses a tight fit; the stationary outer ring can use a loose fit.
  7. Disassembly : Separable bearings are easy to disassemble, but the inner components and outer rings are not interchangeable . The inner and outer rings of the same set of bearings must be used in combination. Do not mix the inner and outer rings of different bearings.

Commonly Used Model Dimensions Table (GB/T297, Unit: mm)

Fields: Model | d Inner Diameter | D Outer Diameter | T Total Thickness | B Inner Ring Width | C Outer Ring Width | r Minimum Chamfer | Cr Basic Dynamic Load ( kN ) | Cor Basic Static Load ( kN ) | Grease Lubrication Limiting Speed (rpm) | Reference Weight (kg)

302 Series (Most General Purpose, Medium Load)

Model d D T B C r Cr Cor Grease Rotation Speed Weight (kg)
30204 20 47 15.25 14 12 1.0 28.2 30.5 7500 0.127
30205 25 52 16.25 15 13 1.0 32.2 37.0 6300 0.160
30206 30 62 17.25 16 14 1.0 43.2 50.5 5300 0.230
30207 35 72 18.25 17 15 1.5 54.2 63.5 4500 0.310
30208 40 80 19.75 18 16 1.5 63.0 74.0 4000 0.400
30209 45 85 20.75 19 16 1.5 67.8 83.5 3600 0.440
30210 50 90 21.75 20 17 1.5 73.2 92.0 3400 0.510
30211 55 100 22.75 21 18 2.0 90.8 115 3000 0.660
30212 60 110 23.75 22 19 2.0 102 130 2800 0.820
30213 65 120 24.75 23 20 2.0 115 150 2400 1.03
30214 70 125 26.25 24 21 2.0 128 172 2200 1.19
30215 75 130 27.25 25 twenty two 2.0 138 188 2000 1.33

303 Series (Heavy-duty model, with greater load capacity)

Model d D T B C r Cr Cor Grease Rotation Speed Weight (kg)
30304 20 52 16.25 15 13 1.5 33.0 33.2 7000 0.165
30305 25 62 18.25 17 15 1.5 46.0 48.0 5600 0.260
30306 30 72 20.75 19 16 1.5 59.0 63.0 4800 0.380
30307 35 80 22.75 21 18 2.0 72.2 78.2 4200 0.510
30308 40 90 25.25 23 20 2.0 90.8 98.0 3600 0.740
30309 45 100 27.25 25 22 2.0 108 118 3200 0.980
30310 50 110 29.25 27 23 2.5 130 142 3000 1.27

322 Series (Wide cross-section, stronger radial load capacity)

Model d D T B C r Cr Cor Grease Rotation Speed Weight (kg)
32206 30 62 21.25 20 17 1.0 51.8 63.8 5000 0.288
32207 35 72 24.25 twenty three 19 1.5 70.5 87.2 4300 0.427
32208 40 80 24.75 23 19 1.5 77.8 96.5 3800 0.515
32209 45 85 24.75 23 19 1.5 80.2 102 3400 0.552
32210 50 90 24.75 23 19 1.5 82.5 108 3200 0.590
32211 55 100 26.75 25 twenty one 2.0 105 138 2800 0.780

323 Series (Extra-wide and Heavy-duty, High Impact Load)

Model d D T B C r Cr Cor Grease Rotation Speed Weight (kg)
32308 40 90 35.25 33 27 2.0 132 160 3200 1.07
32309 45 100 38.25 36 30 2.0 158 192 2800 1.44
32310 50 110 42.25 40 33 2.5 192 235 2600 1.91

Ask About This Bearing.

Send us your specifications and operating conditions to discuss whether this bearing suits your application.

Send inquiry