Product
Needle bearing
NK and NKI are machined-ring single-row needle roller bearings made of high-carbon chromium bearing steel.
Product Description
NK and NKI are machined-ring single-row needle roller bearings made of high-carbon chromium bearing steel.
- NK series: without inner ring. Needles run directly on hardened & ground shaft surface, for minimal radial space. Shaft raceway must reach HRC 58-64.
- NKI series: complete with precision inner ring. No special hardening required for shaft, easy for general assembly.
Key advantages:Ultra-thin radial cross-section, extremely high radial load capacity, high rigidity. Only for radial load, cannot take axial load. Separable construction allows axial displacement between shaft and housing. Cages available in steel or glass-fiber reinforced PA66 polymer (low noise, low heat generation).
Applications
Automotive transmission, clutch, rocker arms, connecting rods, motorcycle drive assemblies; hydraulic pumps & motors, small gear reducers; packaging, textile, wood-working machinery, conveyors; robot joints, cam mechanisms, compact power transmission units.
Selection tip: Choose NKI if shaft cannot be hardened. Choose NK for maximum compactness when shaft can be heat-treated.
Installation Instructions
⚠️Do not strike the needle rollers or cage directly to avoid deforming the cage or damaging the needle rollers.
1.Inspection: For NK, shaft raceway must be hardened HRC58-64 and finely ground. Check all bearing parts for rust, dents or damage.
2.Press-fit outer ring: Apply force only to outer ring face. Never hammer on cage or needles. Heat housing max 120 °C for heavy interference fit, no open flame.
3.For NKI: Press inner ring onto shaft by inner-ring face only.
4.Keep good alignment. This bearing permits axial float; do not apply axial preload.
5.Pre-fill proper grease during assembly. Align outer-ring lubrication hole with housing grease nipple if present.
Maintenance & Cautions
1.Pure radial-load only; avoid axial force and shock overload.
2.Lubrication: Grease for general use; circulating oil for high-speed conditions. Re-grease periodically. Insufficient lubrication causes needle scuffing.
3.Use proper seals in dusty / wet environment. Contamination leads to premature failure.
4.Do not mix components from different used bearings.
5.Store in dry original packaging.
6.For NK series: shaft raceway acts as rolling surface. Worn shaft must be repaired or replaced.
Commonly Used Dimensions Reference Table
Code Explanation: NK: Fw = nominal diameter of shaft raceway, D = outer diameter, B = bearing width; NKI: d = inner ring inner diameter, D = outer diameter, B = width; Cr = dynamic load, C0r = static load (kN)
NK series (solid ring needle roller bearings without inner ring)
| Model | Fw(mm) | D(mm) | B(mm) | Cr(kN) | C0r(kN) | N-oil(rpm) | Mass (g) |
| NK10/12 | 10 | 17 | 12 | 8.6 | 8.0 | 24000 | 14 |
| NK10/16 | 10 | 17 | 16 | 10.8 | 11.2 | 24000 | 18 |
| NK12/12 | 12 | 19 | 12 | 7.2 | 7.1 | 22000 | 17 |
| NK12/16 | 12 | 19 | 16 | 9.2 | 10.1 | 22000 | 22 |
| NK14/16 | 14 | 22 | 16 | 11.5 | 13.2 | 20000 | 26 |
| NK15/16 | 15 | 23 | 16 | 16.3 | 16.6 | 19000 | 28 |
| NK15/20 | 15 | 23 | 20 | 19.5 | 21.8 | 19000 | 34 |
| NK17/16 | 17 | 25 | 16 | 12.0 | 15.0 | 18000 | 30 |
| NK17/20 | 17 | 25 | 20 | 15.0 | 20.0 | 18000 | 36 |
| NK20/16 | 20 | 28 | 16 | 19.6 | 21.2 | 17000 | 38 |
| NK20/20 | 20 | 28 | 20 | 24.0 | 28.5 | 17000 | 47 |
| NK25/16 | 25 | 33 | 16 | 23.5 | 28.2 | 15000 | 48 |
| NK25/20 | 25 | 33 | 20 | 29.0 | 33.5 | 15000 | 58 |
| NK25/30 | 25 | 33 | 30 | 41.5 | 54.0 | 15000 | 85 |
| NK30/20 | 30 | 40 | 20 | 37.5 | 47.2 | 13000 | 78 |
| NK30/30 | 30 | 40 | 30 | 53.0 | 75.5 | 13000 | 115 |
| NK35/20 | 35 | 45 | 20 | 46.5 | 57.0 | 12000 | 92 |
| NK35/30 | 35 | 45 | 30 | 69.4 | 98.0 | 12000 | 138 |
| NK40/20 | 40 | 50 | 20 | 49.5 | 64.0 | 11000 | 103 |
| NK40/30 | 40 | 50 | 30 | 74.0 | 110.0 | 11000 | 155 |
| NK45/20 | 45 | 55 | 20 | 52.0 | 70.0 | 9500 | 114 |
| NK45/30 | 45 | 55 | 30 | 78.0 | 121.0 | 9500 | 172 |
| NK50/25 | 50 | 62 | 25 | 79.0 | 104.0 | 8500 | 175 |
| NK50/35 | 50 | 62 | 35 | 106 | 154 | 8500 | 240 |
NKI series (needle roller bearings with solid inner rings)
| Model | d(mm) | D(mm) | B(mm) | Cr(kN) | C0r(kN) | N-oil(rpm) | Mass (g) |
| NKI12/16 | 12 | twenty four | 16 | 12.0 | 13.9 | 20000 | 36 |
| NKI12/20 | 12 | twenty four | 20 | 14.6 | 18.8 | 20000 | 44 |
| NKI15/16 | 15 | 27 | 16 | 13.0 | 17.0 | 19000 | 38 |
| NKI15/20 | 15 | 27 | 20 | 16.0 | 22.0 | 19000 | 46 |
| NKI17/16 | 17 | 29 | 16 | 13.5 | 18.7 | 18000 | 42 |
| NKI17/20 | 17 | 29 | 20 | 17.1 | 25.5 | 18000 | 53 |
| NKI20/16 | 20 | 32 | 16 | 15.4 | 24.5 | 17000 | 49 |
| NKI20/20 | 20 | 32 | 20 | 19.0 | 32.5 | 17000 | 61 |
| NKI22/16 | 22 | 34 | 16 | 16.2 | 26.5 | 16000 | 52 |
| NKI22/20 | 22 | 34 | 20 | 20.6 | 33.7 | 16000 | 67 |
| NKI25/16 | 25 | 38 | 16 | 18.8 | 31.5 | 14000 | 64 |
| NKI25/20 | 25 | 38 | 20 | 23.5 | 41.0 | 14000 | 78 |
| NKI25/30 | 25 | 38 | 30 | 33.5 | 63.0 | 14000 | 115 |
| NKI30/20 | 30 | 42 | 20 | 27.5 | 44.5 | 13000 | 88 |
| NKI30/30 | 30 | 42 | 30 | 39.5 | 73.0 | 13000 | 130 |
| NKI35/20 | 35 | 50 | 20 | 30.0 | 51.0 | 11000 | 127 |
| NKI35/30 | 35 | 50 | 30 | 44.0 | 84.0 | 11000 | 185 |
| NKI40/20 | 40 | 55 | 20 | 32.5 | 58.0 | 10000 | 143 |
| NKI40/30 | 40 | 55 | 30 | 48.0 | 96.0 | 10000 | 210 |
| NKI45/25 | 45 | 62 | 25 | 44.2 | 82.0 | 9000 | 200 |
| NKI45/35 | 45 | 62 | 35 | 61.0 | 128.0 | 9000 | 275 |
| NKI50/25 | 50 | 68 | 25 | 47.5 | 91.0 | 8200 | 225 |
| NKI50/35 | 50 | 68 | 35 | 66.0 | 142.0 | 8200 | 315 |